Page 64: Software Update Via Satellite Software update via satellite The update has nothing to do with the storage of new TV channels. It is rather meant to update the system software of the receiver. Normally, the update is not required for a trouble- free operation of the receiver. Onida tv software updates firmware update free download where can i. Onida gold 32 inch lcd tv usb software erased how can i update usb software Comag sl65 software update I had download huawei e173 software and tried to update, but when i am trying to update my huawei e173 software, it asks password, please provide m.

Contents • • • • • • • 2005 model The 2005 model uses the same and as the Comag SL65 and Chess SL35. The firmware is also very similar to that used in the Strong SR65xx series, and it can be ported from the Strong SRT65xx to the Silvercrest SL65 and vice-versa. The latest firmware is version 1.75, which corrects the support of some channels. This firmware has to be copied to the receiver by means of a cable. Currently, anyone who has this model of SL65 with firmware version 1.75 or newer is able to watch besides the free-to-air, just a few pay channels that still use older encoding schemes. Silvercrest SL65 Remote Control 2006 model This model uses an chip, and also has a version.

It has the following other differences from the 2005 model: • The 2005 model has screws at the side of the box; the 2006 model does not. • The 2005 model is programmed through a 20 pin interface; the 2006 model is programmed through a 6-pin interface.

2007 model Currently there are 7 models. Chip Pins The Processor chip with 216 small pins will be either an (Ali M3329 B1 or Ali M3329 A1) look for a small thin aluminium plate about 22 mm square, this is the heatsink and has to be carefully removed with your fingernail or a sharp instrument to reveal the number on the face of the processor below it. The heatsink can be replaced afterwards with some thermal paste. If your processor has its heatsink soldered through the main board (On Legs) and has 128 pins it is the Ali M3329C E1 Processor. If it has 208 pins it is the early model and has the Omega STi5518 Processor and this model although is patchable does not have much up to date software releases that will cope with today's current encryptions.

There are current patches for the Ali M3329 B1 Chip and the Ali M3329C E1 Chip, but the Ali M3329 A1 processor has had very little satisfactory success and gives overheating along with pixelation problems due to its internal structure. So basically the A1 Processor is not up to the task of carrying out the necessary algorithms to decrypt today's tighter encryptions. Only when you are confident and know which processor you have got in your STB you can then proceed To Patch or load new firmwares.

Click Pictures Below To Identify Which SL65 Receiver You Have. Ekey control4 driver.

Me, on a Bad Hair Day, holding the SL65. Goodness, you'd have thought I'd have brushed my hair first. Oh, wait, I did.

☺ I received this receiver third-hand, with no instructions, so everything here has been 'figured out'. Somebody sent me the instruction booklet PDF last week (March 23rd) which I downloaded. Since it was a large attachment and my mailbox was maxed out, I decided to delete it (and a few other large messages) and then send a thank you note. Anybody with half a brain (i.e. Not me!) will be wondering exactly how I planned to send a thank you once I'd deleted the email, where would I get the reply to address from? Whoever you are, THANK YOU!

I have printed the user guide in case I need to refer to it, but I didn't do a bad job of figuring out this little receiver. Switching on When you switch the receiver on, the front panel display says ' On', then ' Strt'. After a boot time of about four seconds, we flick to the first channel. The receiver appears to do this rebooting (only a shorter version) when you come out of standby, it appears to power down the reception and video circuitry (in order to save power). Due to the design and operation of the Digibox (i.e. Keeping the EPG up to date), the Digibox really only turns off the picture when you switch it to standby - that's why it always runs hot. Not that running hot is an issue with the SL65!

Startup channel If you don't like the idea of starting on channel 1, you can choose any channel to start on. Choosing which channel to start with. In addition, it appears that if you switch the receiver into standby (not off), it will remember the channel that you were watching, and if you switch it off, then on again the following day (for example), it will restart with the last channel that you were watching. Therefore it would not be unusual to see my receiver start up on channel 0014 which is Anime Central. I think it is a useful feature. You might be less pleased if you switch on and find your kids were watching Babestation or the Playboy One previews. ☺ It is also a useful feature for people such as my mother who might not really want the complexities of learning to use a satellite receiver.